Suche starten
Webmail-Login

Here you get access for your webmail!

Username:

Password:

Tremolo LP

« Back
Tremolo LP

Custom-designed tremolo for Les Paul™*-type guitars. Equally suitable as original bridge and for subsequent conversion. No extra routing work on the body required. Supplied complete with springs and ground sheet. (*Les Paul is a protected trademark owned by Gibson Musical Instruments Corporation)

Can easily be fitted as a replacement for a Tune-O-Matic/tailpiece combination. The dimensions and threaded sleeves match the measurements of our bridges and tailpieces (and correspond to the classic design), which makes it easy to switch between an LP tremolo and a Tune-O-Matic/tailpiece combination and back again.

  • All tremolo systems are supplied complete with mounting accessories.
  • Including a base plate to "earth" the tremolo and two blind screws to cover up any drill holes (see also FAQ30220).

Features

  • Model: Tremolo without Block
  • Tremolo-Block (mm): Without
  • Finish: Polished
  • Surface: Satin-Chrome
  • Options: Right-Hand only
  • Measurements l x w x h (mm): 90x33x10
  • Weight g/item: 210
  • Bore mm: 7
Prod. No.
4204

Images

Technical drawing

To view the complete technical drawing, please use the download file.

Note: Acrobat Reader is required to view PDF files correctly!

User instructions

To view the complete user instructions, please use the download file.

Note: Acrobat Reader is required to view PDF files correctly!

Downloads

User instructions

Technical drawing

Note: Acrobat Reader is required to view PDF files correctly!

Here you will find some additional, useful information about our Schaller product catalog.

Surface finishing

This Schaller Floyd Rose Tremolo is an example of the subtle differences between various surface finishes.

Schaller Tremolo Floyd RoseSchaller Tremolo Floyd RoseSchaller Tremolo Floyd Rose
NI-NickelCH-ChromeSC-SatinChrome
Schaller Tremolo Floyd RoseSchaller Tremolo Floyd RoseSchaller Tremolo Floyd Rose
BC-BlackChromeGO-GoldRU-Ruthenium
Schaller Tremolo Floyd RoseSchaller Tremolo Floyd Rose

SP-SatinPearl

 VC-VintageCopper

For the sake of simplicity, only the right-handed versions of our products are shown in the product images.

 

Measure specifications

All measurements in the product catalogue are given in mm (inch), unless a different unit of measurement is stated.

 

Technical drawings and operating instructions

We do not accept any liability for the correctness of the technical drawings. Prior to installation, please measure for yourself once more, so you can consider regular manufacturing tolerances.

Please note that the technical data can also vary slightly, depending on the surface color. This is due to the difference in the galvanic coating and the galvanic layering, which depends on the color (nickel, chrome etc).

The technical drawings can be printed on one page width. Should the technical drawings not fit on one page, however, please check your print page setup (note: they can be several pages long).

From time to time, the measurements given in the file downloads on our website may differ from those given in the catalogue. Please bear in mind that the measurements given in the online downloads are current. Any discrepancies will be corrected when the catalogue is updated.

Technical Drawings Schaller Tremolo Floyd Rose

 

Bolt- and Screwdistance

Specifics of distance and size in mm (inch):

The functional dimensions of our tremolos in mm (inch) are given in the table below:

TremolosBolt-/ScrewdistanceSleeve gaugeBolt gauge
Schaller Floyd Rose74,5 (2,933)

 7 (0,2756)

5 (0,1969)
Schaller Low Profile74,5 (2,933)

 7 (0,2756)

5 (0,1969)
Schaller Vintage74,5 (2,933)

 7 (0,2756)

5 (0,1969)
Non Finetuning Tremolo 200056,0 (2,2047)

  7 (0,2756)

5 (0,1969)
Assembly Tremolo LesPaul74,5 (2,933)

  7 (0,2756)

5 (0,1969)

 

FloydRose / Schaller Tremolo Nuts

You can find the relevant product numbers in the respective columns with the surface details. The tremolo radius is 12 inches and the nut 10 inches.

NICHSCBCGORUSPVCModelWidth (mm/inch)Radius (inch)Use
381NI381381MC1381391391RU381SP381VCR139,7/1,563010Gibson Flying "V", SG Series
382NI382382MC1382392392RU382SP382VCR241,3/1,626010Old Strat, Kramer Pacer
383NI383383MC1383393393RU383SP383VCR342,9/1,689010Les Paul, narrow spacing
384NI384384MC1384394394RU384SP384VCR442,9/1,689010B.C.Rich, LP, wide spacing
385NI385385MC1385395395RU385SP385VCR544,6/1,755910Boggie Body, Charvel
386NI386386MC1386396396RU386SP386VCR639,7/1,563010Bullet, New Strat
387NI387387MC1387397397RU387SP387VCR741,3/1,626010Bullet, Ibanez

Nuts R8 to R10 are also available on request.

You can find further details and technical drawings in the product catalog in the detailed view on nuts.

 

Tremolo Arms

Here, you can find an overview of the tremolo arms used, including thread diameters.

Tremoloswith knob
6mm		without knob
5mm		knife edge
replaceable
Schaller Floyd RoseXyes
Schaller Low ProfileXyes
Schaller VintageXno
Non Finetuning Tremolo 2000Xyes
Assembley Tremolo Les PaulXno

 

Allen Key

The following table shows you which Allen keys you should use (mm and inch):

Article

Allen keys (mm)

mm

mm

inch

inch

inch 

Schaller Floyd Rose Tremolo

2,5

3,0

 

0,0984

0,1181 

 

Low Profile Tremolo

2,5

3,0

3,5

0,0984

0,1181

0,1378

Vintage Tremolo

1,5

2,5

3,0

0,0591

0,0984

0,1181 

Non Finetuning Tremolo 2000

1,27

2,5

3,0

0,0500

0,0984

0,1181

 

FAQ

FAQ30010 Do Schaller also produce tremolos for left-handed people?

Yes, all Schaller "Floyd Rose" tremolos can also be ordered as left-handed versions. However, the "original Floyd Rose tremolo" we produce must be ordered directly from Floyd Rose (www.floydrose.com). Apart from the base plate, the Schaller and original tremolos are identical to each other.

FAQ30020 Do Schaller produce Floyd Rose tremolos for 7-string guitars?

Yes, we also produce the original Floyd Rose tremolo for 7-string guitars; however, these have to be ordered directly from Floyd Rose (www.floydrose.com).

FAQ30030 Can I order the original Floyd Rose tremolo from Schaller?

No, we do produce the tremolo for Floyd Rose, but you will have to order the original via www.floydrose.com. Of course, our recommendation is to buy the Schaller tremolos, which are identical except for the base plate.

FAQ30040 I have an original Floyd Rose tremolo, but I would like to replace it with a Schaller tremolo now. Is this possible?
Yes, of course. Our tremolo is identical to the original. You may also use our Schaller spare parts for the Floyd Rose tremolo produced by us.
FAQ30050 What is the radius of the Schaller and Floyd Rose tremolo?

The tremolo measures 12 inches and the nut 10 inches (see Technical Drawings in the product catalog under Nuts).

FAQ30060 What is the difference between the R3 and R4 nuts?

Some nuts have the same width dimensions but different designations. The different designations are useful because, although the width dimensions are the same, the pitch is different (see Technical Drawings in the product catalog under Nuts).

FAQ30070 How can I move the bridge saddles on a Schaller tremolo in order to set the intonation?
We supply the appropriate Allen key, which can be used to easily adjust the back parts on the nut.
FAQ30080 How do I need to install a Schaller Sure Claw?

This is very simple: screw the Schaller Sure Claw into the guitar body in place of the spring claw, then re-attach the springs. You can then adjust the spring tension as you want it through a small hole in the cover plate (please drill this yourself) without having to take the cover off every time. Also refer to the illustration on page 25 of the catalog under "Service/Catalog".

Further images can be found in the product catalog "Sure Claw" under "Pictures"

FAQ30090 I have the Schaller Tremstop, but the tremolo arm does not have the matching height. How can I adjust the height?

The height of the Schaller Tremstop can be adjusted; it is possible to - maybe not noticeable at first sight - turn the center piece with the three rings to the right or to the left for height adjustment.

FAQ30100 How can I tighten the Schaller clamp saddles / nuts for the tremolo? Which screws are supplied with it?
Along with the tremolos and nuts, we supply wood screws and steel screws / Allen screws, so you can choose how to attach the nuts yourself i.e. either from the top or from underneath. The nuts are also specially designed so that you can use wood or steel screws without carrying out any modifications whatsoever.
FAQ30110 How can I attach a Schaller tremolo? Which screws are supplied with it?
Essentially, special studs are used to attach the tremolo, together with their own inserts. These have a fine thread. For special applications, we also supply studs with threads which can be screwed directly into the wooden body (i.e. without inserts).
FAQ30120 Are different spring sizes used in Schaller tremolos?
No. The spring sizes on our tremolo systems are optimized and, in general, fit precisely. Please vary the number of springs used in order to obtain the required spring tension.
FAQ30130 Are the same knife edges used for different Schaller tremolos?
Yes. The only difference is between left and right knife edges.
FAQ30140 What is the Schaller spring tensioner (Sure Claw) made of?

Our Schaller spring tensioner (Sure Claw) is made mostly out of zinc, the worm gears are made of brass, and the claw of steel (see NEWS for more).

FAQ30160 The Schaller tremolos have a 12" radius, and the locking nuts a 10" radius. Is it the same for the Floyd Rose tremolos that Schaller also produces?
This is related to the taper of the fingerboard and has, in all previous experience, resulted in optimal playing properties. 12" and 10" measurements are the most frequently used sizes in the guitar industry.
FAQ30170 The Schaller tremolos have a 12" radius, and the locking nuts a 10" radius. Is it the same for the Floyd Rose tremolos that Schaller also produces?
Yes, that is exactly right, the radii are the same. These measurements are the ones most frequently used in the guitar industry, and are proven to be effective.
FAQ30180 Do you also manufacture the R8, R9, and R10 nuts?
Yes, please submit a special request to us. We will then ship them directly.
FAQ30190 What can I do if I have removed the Schaller Tremstop several times and the adhesive no longer holds properly?
Please request a new adhesive pad from us. This is a special type of adhesive tape, which holds extremely well to the guitar body without damaging the surface.
FAQ30200 I bought the Schaller LP tremolo and found out that the pitch is too high. What do I need to do?

This tremolo is a little more difficult to use due to its missing tremolo block and the fact that the springs can not be adjusted. Therefore please use the tremolo slowly only. To change the pitch please turn down the height adjustment screws as far as possible. If the string tension is not sufficient to balance the tremolo, you might try to remove or replace the middle tension spring. Everything depends on the string thickness, as well (ask guitar maker).

FAQ30210 Does the Schaller LP tremolo travel in both directions (up and down)?
Yes, it does. Our Schaller Assembly Tremolo LP was specially developed for simple replacement of the original bridge on Les Paul guitars. Please use this tremolo in accorance with the design i.e. carefully. Incidentally, all Schaller tremolos travel in both directions.
FAQ30210 All of the drive-in sleeves on my Schaller LP Tremolo are too small. What can I do?
The drive-in sleeves for our Schaller LP Tremolo have a diameter of 10mm. Unfortunately, we cannot provide an appropriate sleeve for every imaginable size, and have thus decided to use only one size, i.e. the size that is used most frequently in the guitar industry. In these special cases, you should therefore contact a guitar maker who can work either with changes to the guitar body or with spacer sleeves.
FAQ30220 What is the base plate supplied with the Schaller LP-Tremolo used for?

The base plate is used to earth the tremolo, i.e. to avoid disturbing interference. If you are making the change from a combination such as our Schaller stop-tailpiece and a GTM bridge to the LP tremolo, please proceeed as follows: Place the LP tremolo in place of GTM bridge and connect it together with the base plate to the stop-tailpiece.

We also supply 2 blind screws together with the Schaller LP Tremolo, so you can cover the resulting holes should you wish to remove the stop-tailpiece completely. In this case, use the LP tremolo together with the blind screws. In our product catalog, you can find an additional image of our LP tremolo which shows you how it is attached.

FAQ30230 Is there a difference in the baseplate between the Schaller tremolo and the Floyd Rose II tremolo?
No, the dimensions and the material are identical.
FAQ30240 What material do you use to make the Schaller tremolo blocks?

Schaller's "Original", "Floyd Rose" and "Low Profile" tremolo blocks are made of brass, and the "Vintage" and "2000" blocks are made of zinc.